Protection against spam bots. Please answer the following question: What year is it this year?
309 results found for your search term: „Rectangular Frame Pet Pool Set, with Filter Pump and Ramp (220-240V) (48404NP)“
The following results contain only part of the search terms:

Saltwater System Without Filtration
The solinator cannot operate without the filtration on because it does not have its own pump to pump the water. If it is connected to the filtration with the solinator, it automatically switches on with it. Without filtration it will remain idle and display a water flow error.

Getting the pool ready for winter
How to properly winterize a pool - the procedure for leaving the pool assembled as well as disassembling and storing it. Important steps include cleaning the water, adding winterizing chemicals, disconnecting accessories, and proper storage of the tarp and pool cover.

Will the saltwater system work without the filtration running?
No, a saltwater system will never work without filtration. The saltwater system does not have its own pump to draw water from the pool. It is essential that the saltwater system is connected BEHIND (AFTER) the filter pump and that the filtration is on. If the saltwater system is turned on without filtration, the saltwater system will not turn on and most likely an error message 90 (insufficient water flow) will appear. At the same time, however, the saltwater system will not be damaged, it will just remain idle and not produce chlorine. If you have the filter pump with built-in saltwater system, the saltwater system will automatically switch on the filtration.

Setting up the EasySet pool
The correct assembly of the EasySet pool has a major influence on its stability and durability. The key is to choose a firm and level surface, use a pad, lay out the shell correctly and do not over-inflate the inflatable ring. It is also important to avoid common installation mistakes that can affect the functionality of the pool.

Does the filter pump keep the pool walls and bottom clean?
No. The filtration will keep the pool water free of mechanical debris such as leaves, twigs, insects, etc. A pool maintenance kit should be used on the bottom of the pool. If your pool set does not include this accessory, you can purchase it. Pool vacuums are also available. INTEX can also offer you the Krystal Clear saltwater system, which will keep your pool free of debris, algae and bacteria. Depending on the local water conditions, it may be necessary to add pool chemicals to make the water clear and less hard. For further advice, we recommend that you consult a pool specialist in your area.

Setting up the Frame pool
Setting up a swimming pool with structure requires a firm and level surface, sufficient space and correct fixing of the supports. The metal structure should be treated with talcum powder before assembly for easier handling. During filling, it is important to check the tension of the belts, the alignment of the supports and the correct position of the corner pieces.

How to drain a swimming pool? How to drain the last 10 cm of pool water? The siphon principle.
For instructions on draining the pool water and information on winterizing the pool, see the article below (Winterizing the Pool).If you have trouble draining the last 10 cm of pool water, here are some suggested solutions:1. If the water level drops below 10 cm for Metal/Prism/Ultra pools, you can remove one vertical leg and all horizontal beams and place them on the ground. The water will then start to drain.2. You can use a pool drain pump (catalog number 28606) or the siphon principle to drain rectangular pools. How to drain a swimming pool using the siphon principle Option A Connect a garden hose to the water supply. Place the free end of the hose in the swimming pool. Run water from the water supply into the hose. When the water starts to flow into the swimming pool, leave the end in the pool submerged in the pool water and turn off the water supply. Then unscrew the end from the water supply. This end will start to flow water in the opposite direction, i.e. out of the swimming pool.  Option B Immerse the garden hose completely in the swimming pool so that air can escape from both ends and the hose fills with water. Then fold the hose approximately 30 cm from the end at one end so that water does not flow out of this end. Remove the folded end of the hose and straighten the hose where you want the pool water to flow out.